Original Wireless Duplicator Remote Control Copy 433MHz Universal Garage Door Transmitter

Wireless
Cloning Remote Control Universal Copy Remote for PT/SC/LX/HX/HT
Series 433MHz

Cloning chip
types:

2260(PT2260, SC2260, LX2260, HX2260); 2262(PT2262,
SC2262, LX2262, HS2262, HX2262); PT2264, PT2240(LX2240); 1527(EV1527, HS1527,
HX1527); FP527, CS5211, SMC918, SMC926, AX5026, AX5326-3, AX5326-4, HT600,
HT680, HT6207, HT6010, HT6012, HT6013, HT6014, HT12D, HT46F49E, PIC16F629,
PIC16F630 etc.
Note: Besides the above chips, it can also clone part of HCS101, HCS200 and
201, HCS300 and 301. However, cloning rolling chips is normally not
recommended. Because there are many uncertainties during cloning rolling chips.

Use steps:
1. Clear code: two fingers at the same time hold the unlock key and lock key;
the LED light rapidly flashes 3 times in about 2 seconds; let one of the
fingers go (the other hand can not let go), and then use the loose finger to
quickly click three times on the loose button until the LED light flashes
quickly; the two fingers can release; then press any one key of the remote
control; when LED light goes off, it means clear code is successful(four keys
all empty); if after you press any button of the remote control, the light is
still on, it indicats that the original code has not been cleared successfully.
You need to re-clear, and only successfully clearing the code can cloning be
successful. You can repeatedly clear and clone the code.

2. Copy: left hand taking the original remote control, right hand taking our
cloned remote control and keep two remote control as close as possible; press
the first keys of two remote controls at the same time; in about 2 seconds, the
LED light will flash quickly 2 times; after one second, the indicator light
keeps flashing and let go of your fingers; and then press the key after
successful study, the light keeps on, which means that the first key code on
original remote control has been copied to the other remote control; the same
method can be used in turn on the second key, the third key… If the copy is
successful, the remote control function is the same as the original matching
remote control.

3. Restore: When you accidentally clear the copy of the remote control code,
you can simultaneously press the copy of the remote control of the bottom two
keys, LED lights will flash quickly, let go after pressing any key, light long,
this Indicating that the code for the remote control is restored. Before using
our duver remote control, please be sure to remove the existing code from the
remote control.

4. How to deal with the situation where some of the keys can control, the rest
can not control? You can use clear and restore operation, the specific
operation is as follows:
(1) first clear code;
(2) after clearing code, copy the unsuccessful key again, and there is no need
to copy the rest buttons;
(3) and then clear the code again;
(4) restore code; at this time, the original keys that were not successfully
copied are now covered by new codes, and the original keys that were
successfully copied are now retained. If there is no copy after the second copy
of the keys, repeat the above steps again and again until all keys are
successfully copied.

Specifications:
Rated voltage: 12V
Rated current: 10mA
Product weight: about 26g
Installation: Wireless
Corresponding frequency: 433MHz
Modulation: ASK (amplitude modulation)
Wireless transmitting distance: 50-100m (open space)
Scope: garage doors, alarm, automatic doors, shutter doors, and so on

Precautions:
1. Select the remote control of the prerequisite: the original remote control
function is normal, remote control chip is the same or compatible, remote
control operating frequency the same.
2. The remote control can only copy the fixed code, learn the code chip and
part of the single-chip remote control (can copy the chip model see copyable
chip type).
3. Two-way remote control, rolling code remote control, single-chip encryption
program remote control can not be copied. Such as HCS200, HCS201, HCS300,
HCS301 and so on.
4. Before copying the remote control, make sure that the existing code on the
remote control has been cleared and check that the code is cleared
successfully. Otherwise, it can not be copied.
5. Please ensure that your remote control has enough power, the distance
between the two remote control the better! If the copy distance is too close to
the switch at different angles to copy. Press and hold the button on the
original remote control to send the signal completely normal, and then press
the button on the remote control to ensure that the function is completely
copied.
6. This note is all B procedures for the unified use of the remote control
instructions, not for each style dedicated to a description of all duody remote
control operation methods are basically the same, please be flexible, reference
to use, do not know can consult in advance. You can also refer to our copy of
the remote control operation demonstration video operation.